What can X-TREME tape be used for ?

What can X-TREME tape be used for ?

Leak Mate X-TREME Tape Suggested Uses • M.D.P.E Pipe Repair• Emergency Radiator Hose Repair • Water Hose & Pipe repair • Boat Rigging • Coating ends of Rope • Home & Garden • Corrosion Protection • Electrical Insulation • Weatherproofing Electrical Connections • Wiring Harnesses • Wire Bundles • Sealing Electrical Connections • Plumbing Repair • Emergency O-Rings & Seals • Sport & Tool Handles • And much, much...

HOW TO STOP A LEAK

Learn how to cope with this plumbing emergency before it happens. Find out how to turn off the hot and cold water supply so that you can minimise the damage when a pipe bursts, and have the basic tools somewhere handy. But never try and repair a leaking boiler – call in a professional instead. Time to complete job: About 30 minutes. Approximate budget: Emergency plumbing kits including a pipe repair kit, spare valves and tap washers cost around £12. Tip: If someone has hammered a nail into a pipe, don’t try and remove it, as this will make the leak worse. For professional advice, visit The Association of Plumbing and Heating Contractors. Step 1: Turn off the water supply Cold water: Turn off the main stopcock that is usually in the kitchen. This will stop the flow of cold water into the house. This is normally a brass valve with a circular handle. Hot water: It’s important to switch off your boiler and immersion heater before draining the hot water. Then, turn off the valve on the cold feed pipe to the cylinder and run all the hot water taps to get rid of water in the pipes. Step 2: Tie up the ball valve If you can’t find the cold feed pipe valve, tie up the ball valve in the cold water tank and turn on all the cold water taps to empty the remaining water in the tank. When no more water comes out, run the hot taps until these run dry as well. Tip: You should also turn off the electricity if the water leak is near wiring, sockets or switches. Step...

Preparing your home for a sudden freeze

Preparing your home for a sudden freeze Before the temperature drops below zero and winter hits us, a quick check on the following can save you time and money. 1) Make sure pipes are lagged All visible pipes, particularly exposed pipes in crawl spaces in the attic, should be lagged with pre-formed foam (the type that wraps around the pipes) available from plumbers’ merchants and DIY stores. Remember, the thicker the lagging, the better: a minimum of 50mm in diameter but preferably 75mm. When insulating bends and tricky-to-reach pipes use gaffa tape to fix it securely. 2) Make sure your tank is insulated The best option is a preformed jacket that hugs the tank (a bit like the Puffa jackets from the 80s!) They’re filled with glass fibre matting and attach securely to the tank – this is important as you don’t want it to dislodge. With the exception of a header tank in the loft which should be completely enclosed, there should be no insulation beneath your tank as this will prevent warm air rising from below, increasing the likelihood of it freezing. 3) Repair dripping taps If you have any dripping taps replace the washers. If dripping taps freeze they’ll block your pipe and cause damage. How to deal with a frozen pipe You’ll know if you have a frozen pipe because one or more of your taps won’t work but before you start on your frozen pipe action plan it’s worth first checking with the neighbours that they have water – if they don’t it’s likely there’s a problem with local supply. Assuming you do have...

Burst and frozen water pipes can cause untold damage to your home so here are some tips to avoid it during the freezing conditions.

Burst and frozen water pipes can cause untold damage to your home so here are some tips to avoid it during the freezing conditions. London fire crews went to 163 floodings in the last four days of November, up 150%, with Thames Water answering 150 reports a day, twice the seasonal norm. Frozen Pipe Emergency A frozen pipe is an emergency, because this will cause it to burst causing thawed water to come pouring from the break. The following steps describe what you should do as soon as you discover a frozen pipe: 1. Turn off the water supply: Thousands have had water supplies disrupted due to burst pipes Turn off the main stop tap. You should find this under the kitchen sink or where the service pipe enters your home. Turn off the stopcock in your cold water tank if you have one, it’s usually found in the attic or loft. 2. Beat the burst: Protect everything around the pipe that appears to be frozen to avoid damage if it bursts. 3. Thawing out: Open the tap nearest to the part of the pipe you think is frozen so the water can flow through when it has melted. Thaw the ice in the pipe with a hot water bottle or hairdryer (taking care to keep it well away from any water), beginning from the tap end and working back toward the cold water tank. Never use a heat gun or blow torch. Preventing Burst Pipes – Winter Care If a burst pipe leaks and water comes gushing through the ceiling, it can wreak real damage on your home...

Why is Leak Mate for the Plumber Electrician Joiner Builder Decorator and DIY Enthusiast?

Why is Leak Mate for the Plumber, Electrician, Joiner, Builder, Decorator and DIY Enthusiast? Let’s picture it, you have put a heating system in and filled it up cold, you fire up the boiler and the system is getting hot with rising pressure and temperature, a fitting starts leaking, The time it takes to drain the system down, is enough time to cause damage to the customer’s home, you put a bowl under the pipe to catch the water only to find you can’t get it out again, it’s messy and worrying and the last thing one wants is an insurance claim, or to reduce your bill because of damage caused by the leak.  Leak Mate is a unique reusable tool that will stop leaks in seconds allowing time to safely drain the system. The tool is supplied with reusable 10 15 & 22mm seals that have a recessed step moulded in every seal to fit copper fittings.Leak Mate also seals split pipes and holed pipes whether plastic or copper up to 10 Bar. The product has been field tested by a plumbing company over the last 2 yrs.Leak Mate is an essential tool for all Tradesmen and homeowners as a temporary fix allowing minimum disruption. The Leak will need to be fixed at a more convenient time by a qualified plumber. There is no comparable product currently available in the market place. The Leak Mate Tool provides a quick easy solution to a variety of sizes of leaking pipe and fittings and the tool is re-usable time and time...